Audi A6 infotainment carrier made from Lanxess composites
October 09, 2014 - Germany
The Audi A6 is using an infotainment carrier for the first time, made from a continuous fiber-reinforced polyamide composite and a polyamide 6 overmolding material, which has been fabricated with Tepex and Durethan from LANXESS.
The composites-made infotainment carrier and mass-produced component weighs only just over half as much as its steel counterpart and was preceded by a production-ready prototype.
For the manufacture of the prototype, KraussMaffei developed a fully automated manufacturing cell with a specially adjusted handling system and a heating unit directly positioned above the mold platen.
Based on this work, Reinert Kunststofftechnik GmbH und Co. KG built an optimized manufacturing cell for the fully automated and reproducible series production of the infotainment carrier.
The process involved use of two inserts made of Tepex dynalite 102-RG600(2)/47%, a polyamide 6 composite from LANXESS subsidiary Bond-Laminates reinforced with continuous glass fibers.
They are gradually heated by an infrared heating system from KRELUS AG, formed in the injection mold and then directly overmolded with the easy-flow polyamide 6 Durethan BKV 30 EF H2.0 from LANXESS.
Ribs on the side of the component far from the gate are filled by injecting Durethan through the Tepex inserts.
The one-shot process enables production of the composite part in a cycle time of less than 50 seconds without requiring any re-working.
Special grippers rapidly transfer the heated composite inserts to the mold, where they are set in place by special positioning pins.
The holes for the screw connections are not stamped afterwards in a separate processing step, but rather formed by mandrels inside the injection mold when it is closed.
This way, the fibers are pushed around the bore hole with virtually no damage at all, which ensures optimal load transfer when the component is exposed to stress.
This positive effect has been confirmed by corresponding testing. The handling system and production mold were developed and manufactured by Maier Formenbau GmbH.
The infotainment carrier holds a premium-brand amplifier and an optional TV tuner.
It must not only display high stiffness, but also be resistant to fatigue at the points where it is connected to the body and add-on parts, because the weight of the installed devices leads to vibrations during driving, which causes high dynamic stresses.
These areas therefore were reinforced with Tepex and designed such that forces flow mainly via the continuous fibers. (AR)
The composites-made infotainment carrier and mass-produced component weighs only just over half as much as its steel counterpart and was preceded by a production-ready prototype.
For the manufacture of the prototype, KraussMaffei developed a fully automated manufacturing cell with a specially adjusted handling system and a heating unit directly positioned above the mold platen.
Based on this work, Reinert Kunststofftechnik GmbH und Co. KG built an optimized manufacturing cell for the fully automated and reproducible series production of the infotainment carrier.
The process involved use of two inserts made of Tepex dynalite 102-RG600(2)/47%, a polyamide 6 composite from LANXESS subsidiary Bond-Laminates reinforced with continuous glass fibers.
They are gradually heated by an infrared heating system from KRELUS AG, formed in the injection mold and then directly overmolded with the easy-flow polyamide 6 Durethan BKV 30 EF H2.0 from LANXESS.
Ribs on the side of the component far from the gate are filled by injecting Durethan through the Tepex inserts.
The one-shot process enables production of the composite part in a cycle time of less than 50 seconds without requiring any re-working.
Special grippers rapidly transfer the heated composite inserts to the mold, where they are set in place by special positioning pins.
The holes for the screw connections are not stamped afterwards in a separate processing step, but rather formed by mandrels inside the injection mold when it is closed.
This way, the fibers are pushed around the bore hole with virtually no damage at all, which ensures optimal load transfer when the component is exposed to stress.
This positive effect has been confirmed by corresponding testing. The handling system and production mold were developed and manufactured by Maier Formenbau GmbH.
The infotainment carrier holds a premium-brand amplifier and an optional TV tuner.
It must not only display high stiffness, but also be resistant to fatigue at the points where it is connected to the body and add-on parts, because the weight of the installed devices leads to vibrations during driving, which causes high dynamic stresses.
These areas therefore were reinforced with Tepex and designed such that forces flow mainly via the continuous fibers. (AR)